Lead - acid battery charger By LM317 ,LM350 | Circuit Project Electronic

Lead - acid battery charger By LM317 ,LM350

Source : http://www.vt52.com

There are many circuits available for charging batteries, but many are for NiCd or NiMH batteries. They will not work for lead/acide batteries, so don’t use these!!! The best way to charge a battery is with a current limited voltage regulator. This sets a maximum current (say 1A) that will flow to charge the battery. If the current rises over this set current, the regulator will be forced to put out a lower voltage. Since voltage drops, so will the current; hence current limited. While the battery is charging, the current should decrease slowly while voltage starts to increase. In the end the current will be next to zero and the voltage will be equal to the set voltage.

Use the following to design a charger:

1) The charging current should be kept to around 0.1 times the capacity of the battery. So a 10Ah battery should be charged with 1A of current (10 x 0.1 = 1). The battery will not be forced (quick charged) this way and assures a longer lifetime.

2) The charging voltage should be set to 2.3 - 2.4V per 2V cell. So a 12V battery (6 cells of 2V) is charged at 6 x 2.3 = 13.8V.

3) The transformer winding for the charger supply is chosen at the charging voltage plus 3V regulator drop plus 1.4V rectifier drop (two diodes) plus 10% safety. So for a 2V battery, the winding (AC) is 2V + 3V + 0.7V + 0.7V = 6.4V + 10% = 7V.

4) The charging current is limited by the small resistor in the common leg of the charger. The value for this resistor can be calculated with: R = 0.6V / max current. So if I want a maximum current of 0.5A, I will need 0.6V / 0.5A = 1.2 ohms. The 0.6V is the voltage required for the transistor to go fully into conduction. Between 0V and 0.6V the transistor will adjust the regulator to increase or decrease voltage depending on the current it is passing.

5) The charging voltage can be set using the potentiometer. Just hook up a volt-meter to the charger (without the battery attached) and adjust the output voltage until it macthes the charging voltage. Use a 1K pot for 2V batteries, use 5K for 6V and 12V batteries.

6) Use an extra fuse on the charger, about two times the maximum current you are charging with. Fusing is critical for safety reasons. A battery can deliver 100+ amperes during a short, so it can cause serious damage or even fires when something goes wrong with the charger. Put the fuse behind the regulator in the lead going to the battery. This fuse is not to protect the supply from a short in the charger, but to protect everything else from the battery in case of a short anywhere. Don’t forget to fuse the primary winding of the charger as well…

7) You’re set up to charge…

The diode over the regulator in my schematic prevents damage to the regulator when the supply is turned off. In this situation the battery that is still attached offers a negative voltage over the regulator, as the voltage on the output is greater than the voltage on the input. The diode shorts the regulator in this situation and avoids any problems. It is just a safety.

Click to Read More

Power Supply   Switching Power Supply   DC to DC Converter   Inverter
Battery charger   Led flasher   Motor speed controller   LM317   IC 741
RF radiofrequency   Electronic control   Digital Circuit   Alarm home system
DC to DC converter step up voltage   Mini project   Temperature control
FM receiver   Dual power supply   Fluorescent lamp   Pic microcontroller
Led display   RF amplifier   FM transmitter   LM324   LM723   TL494
2N3055   LM338   SG3525   Li-ion battery charger   Pulse generator